Call (954) 378-8564
Home / Service Areas / Hollywood Beach

Broadwalk Era Apartments and Hollywood Beach Wiring

Hollywood Beach is a place of small apartment buildings, older condos and busy rentals beside the Broadwalk and the Intracoastal. This page is for the owners, landlords and managers who keep those buildings powered.
Illustrative photograph
Illustrative photograph

Buildings that grew up beside the Broadwalk

Walk along the Hollywood Beach Broadwalk and you pass a long run of buildings that tell the story of a beach town. There are small apartment houses with outside stairs, older low rise condominiums with balconies facing the sea, newer towers rising above them, and shops, restaurants and hotels that serve the foot traffic. State Road A1A runs close by, and the Intracoastal Waterway lies a short distance to the west. The result is a narrow strip of land that holds a lot of people and a lot of buildings, many of them older and many of them heavily used.

The older buildings were typically built when electrical needs were much lower. A small apartment might have been designed with a modest panel, a few circuits, a window air conditioner and a few outlets. Over time, central or ductless cooling replaced window units, kitchens received newer appliances, and residents added computers, televisions, chargers, fans and portable heaters. The buildings were adapted as they went, and the wiring was patched and extended. Today it is common to find an old distribution system carrying a much heavier load than it was built for.

The nature of occupancy adds to the stress. Many units are rented by the week or the season, some are occupied year round, and some sit empty for long stretches. Systems that run constantly or intermittently under such varied conditions age differently. A unit that is closed up with the air conditioner off for a month can develop mold and moisture problems. A unit that is full of guests in July may overload circuits that were never meant for a crowd.

Another factor is shared responsibility. In most multi unit buildings, a building owner, association or management company controls the main service, meter rooms, risers and common area lighting, and individual owners or tenants control what is inside a unit. Problems that affect several units usually originate in shared equipment, while problems confined to one unit usually originate inside it. Knowing which is which speeds up repairs and avoids needless work.

This page is a general guide for people who own, manage or live in these buildings. It does not describe any specific property. A quote can begin with a call in which you describe the building, but meter rooms, risers and panels need an on site visit before any plan is final. We cover the shared systems first, then individual units, rentals, exterior items and storm planning.

Meter rooms, risers and the shared backbone of a building

Most multi unit buildings have a meter room or meter bank where the utility's incoming service is distributed to individual meters. From each meter, a feeder runs to the unit's panel. In taller buildings, vertical runs called risers carry power between floors. This is the backbone of the building. When it works, nobody thinks about it. When it fails, many people are affected.

Meter rooms near the beach face the problems of salt air and humidity. Rust on enclosures, corrosion on lugs, moisture on the floor, and insect nests in gaps are common. Because these rooms hold equipment that carries large currents, a failing connection can produce serious heat. A periodic inspection by a qualified electrician is a wise investment. It may include a visual check, a look for heat discoloration, tightening of connections where appropriate and thermal imaging to find hot spots under load.

Access and labeling are important. Meter rooms should be kept clear, locked against tampering, and labeled so that each meter and disconnect can be matched to a unit. In older buildings, labels fade or are wrong because units were renumbered. A mislabeled disconnect can lead someone to shut off the wrong apartment or, worse, to work on a circuit that is still live. A relabeling project, done carefully with verification, is time well spent.

Capacity is another matter. A building's service has a ceiling. When units add heavier loads, the cumulative effect can approach the limit. Signs include lights dimming throughout the building when central equipment runs, breakers tripping in the main, or the utility noting that equipment is overloaded. A load study by a professional can show how much room remains and what options exist if more capacity is needed.

Grounding and bonding in an older building deserve a check. Over time, corrosion and renovation can compromise the connections between the building's metal systems and the grounding electrode. A weak ground makes surges and faults more dangerous. An electrician can test and correct it.

Common area systems include hallway lights, stairwell lights, exit signs, emergency lighting, elevators, pumps, gates and sometimes pool equipment. Each should be on a circuit with appropriate protection, tested on a schedule and documented. Emergency lighting that does not work during a power failure puts residents in the dark exactly when they need light. Test it, record the results and repair failures promptly.

Finally, associations should keep a binder, physical or digital, with one line diagrams, panel schedules, inspection reports and contractor contacts. Boards change. Records keep the building's knowledge from leaving with them.

Inside the unit: panels, circuits and the limits of an older apartment

Inside a typical older beach apartment, the electrical story is compact. There is a small panel, often near the entry or in a closet, with a main breaker and several branch breakers. There are circuits for lights, outlets, the kitchen, the bathroom, the air conditioning and perhaps a water heater. The details vary, but the proportions are small, and the demands of modern living can exceed them.

The kitchen is the first place where limits show. Today's kitchens use a refrigerator, a microwave, a toaster, a coffee maker, a dishwasher and sometimes a disposal, all in a space that may have only one or two circuits. Code now expects multiple small appliance circuits for counters, plus dedicated circuits for the major appliances. If your kitchen trips a breaker whenever two appliances run together, the circuit arrangement may need improvement. Ground fault protection is expected in kitchens and baths, and older units may not have it.

Air conditioning is the next. A unit that has been upgraded from window units to a ductless or central system needs a dedicated circuit sized to the equipment label. If the new system was added on an existing circuit, or with undersized wire, it can overheat. The circuit must match the label's minimum circuit ampacity and maximum breaker size. Check that the disconnect near the outdoor unit is in good condition, clean of corrosion and properly sealed.

Panels inside units can be tight. Many older units have little room to add breakers, and some have panels that are themselves a concern because of age or design. If you want to add circuits or equipment, an electrician will review the panel. In a condo, you may need association approval to replace a panel, and the work may need coordination with the building's service.

Here are signs that an older unit needs attention:

  • Flickering or dimming when appliances start.
  • Outlets or switches that are warm, loose, cracked or discolored.
  • Breakers that trip repeatedly or will not stay on.
  • Buzzing from the panel or a smell of hot plastic.
  • Extension cords and power strips used as permanent wiring.
  • A lack of outlets in bedrooms and living areas.

Small fixes can make a big difference. Adding outlets, replacing worn devices, adding ground fault protection and relabeling the panel can transform a unit. Plan improvements in order of safety. Replace anything that heats, sparks or smells first. Then add capacity. Then add convenience. Coordinate with building rules on hours, insurance and approvals before work begins.

Finally, take photographs of your panel and keep a simple list of what each breaker serves. It will save time whenever a repair is needed.

Rentals, turnover days and guest loads

Rental owners along the beach live with a rhythm of arrivals and departures. A fast turnover is a chance to catch electrical problems before they affect the next guest. Building a short routine around it pays off.

At each turnover, test the smoke alarms and, where installed, the carbon monoxide alarms. Press the test button and confirm that the alarm sounds. Check expiration dates printed on the units, and replace those that have expired. For interconnected alarms, confirm that testing one sounds all. Our page on wired and battery smoke alarms explains how the systems differ.

Test ground fault outlets. Press the test button on each ground fault receptacle in kitchens, baths and outdoors, confirm that power cuts off, and press reset. If a device does not trip or does not reset, replace it. Use a simple plug in tester on ordinary outlets to check for wiring faults.

Inspect cords and plugs on appliances you supply. Fans, lamps, kettles, coffee makers and televisions endure much handling in a rental. Replace any cord that is cracked or frayed, and any plug that is loose or warm. Do not provide space heaters unless they are modern and in good condition, and consider not providing them at all in a warm climate.

Look at power strips. Guests plug in many devices. Strips with overload protection are better. Leave one or two in sensible places, and make sure guests do not need to chain them. Provide enough outlets by beds and near seating so that improvisation is unnecessary.

Provide clear instructions. A one page sheet showing where the panel is, how to reset a breaker, who to call and what to do if the power fails reduces stress and calls. Label breakers with plain names. Avoid labels that only make sense to the owner.

Think about peak load. A unit that sleeps six may run the air conditioner, a microwave, a hair dryer and several chargers at once. The circuits should handle it. If guests report frequent breaker trips, that is a sign to investigate. Do not just tell them to avoid using two things at once.

Document each turnover check with date and results. A short log supports insurance claims and demonstrates diligence. In the event of an incident, it helps show that the unit was maintained.

Lastly, use turnover days for quick preventive tasks, like tightening the cover screws on the panel and checking for rust or moisture. If something looks wrong, call before the next guest arrives.

Salt, balconies and the exterior of a beach building

Exterior electrical equipment on a beach building lives a tough life. Balcony lights, stair lights, walkway fixtures, outdoor outlets, meters, disconnects and air conditioning condensers all face salt and wind. The cumulative effect of years of exposure is visible on any older beachfront building.

Start with fixtures. Corroded housings, cloudy lenses, failed gaskets and loose mounting screws are common. Fixtures with failed seals let in water, which corrodes the sockets and wiring inside and can cause shorts. Replace such fixtures with versions made for harsh environments. Use stainless or coated fasteners, and apply anti seize where metals differ. Seal around where fixtures meet the wall.

Balcony outlets need special mention. They sit in the weather, often under a thin cover. Ground fault protection is expected on them, and in use covers that seal over a plugged in cord are the right choice. In many buildings, balcony circuits are fed from the unit panel and may be shared with other outdoor devices. If you notice that an outdoor outlet works intermittently or trips its protection after rain, do not ignore it. Water in the box is the likely cause.

Stairs and walkways need lighting for safety. In a building with outside stairs, lighting failures create trip hazards and liability. Choose fixtures with long life lamps and corrosion resistant housings, and put them on timers or photocells. Check that circuits are protected and that cable entries are sealed.

Air conditioning condensers on roofs, balconies or pads are exposed to salt and sun. Disconnects near them should be weatherproof, in good condition and clean of corrosion. Condenser coils corrode as well, and a failing unit may draw extra current, stressing the circuit. Regular cleaning and servicing by a heating and cooling professional extends life and reduces electrical strain.

Meters and meter bases on exterior walls can corrode, crack or leak. Report any damage to the building management and the utility. Do not open a meter base yourself.

Finally, think about visual inspections as a habit. Once a season, walk the exterior with a notebook and a camera. List rust, cracked covers, missing screws, damaged conduit, and fixtures that do not work. Share the list with management or your electrician. Small repairs are inexpensive. Neglect is not.

Where changes are planned, remember that exterior work on a multi unit building may need association approval, permits and coordination with other trades such as painters and waterproofing contractors. Make sure sealing work respects the electrical penetrations.

Storm season and planning for the whole building

Storm season is a test for every beachside building. Wind, surge and long outages stress electrical systems and residents. A building that plans ahead comes through better.

Before the season, review the basics. Confirm that meter rooms and electrical rooms at ground level are protected from water as much as possible. Check that doors and seals are intact. Keep equipment off the floor when possible. Verify that emergency lighting and exit signs work, and that generators serving common loads are serviced and tested. Make sure fuel is stored safely and the generator is located where exhaust cannot enter the building.

Educate residents. A simple notice explaining what to do before and after a storm helps. Advise residents to unplug sensitive electronics, to avoid using elevators during outages, to stay away from downed lines, and to never run generators indoors. Provide contact information for management and for the utility. Encourage residents to photograph their units for insurance.

After a storm, treat electrical rooms with caution. If water has entered, do not enter and do not operate switches. Call the utility and a qualified electrician. Equipment that has been submerged needs evaluation, and in many cases replacement. Our storm damage repair page and our page on what to expect when power returns after a storm describe the sequence.

Surge protection is a building wide matter. A surge protective device at the main service guards the whole building, and devices at unit panels add another layer. Residents can add point of use protection for sensitive electronics. Power returning after an outage can arrive with spikes, so waiting a few minutes before turning equipment on is wise.

Plan for those who rely on electricity for medical reasons. Management should know which residents need assistance and have a plan for communication and support. Residents should have their own backup arrangements.

Consider a longer view. An older building may benefit from a phased improvement plan: inspect the meter room, address corrosion, relabel everything, test emergency lighting, update panels that are past their useful life, and add surge protection. Spreading work over a few budget cycles can make it manageable. Prioritize safety items first.

If you manage or own a building near the Broadwalk and want help thinking through a plan, call and describe the situation. A quote can start by phone, and shared systems need an on site visit.

A worked example shows how a building wide plan can come together. A small association manages a four story building a block from the Broadwalk. The board hears complaints of lights dimming in the hallway each afternoon, sees rust on the meter room cabinet, and learns that two unit owners have replaced window units with ductless systems. They call an electrician for a walk through. The visit shows a corroded lug on one meter position, a feeder that runs warm under afternoon load, hallway lights sharing a circuit with the elevator controller, and emergency lights whose batteries no longer hold a charge. The plan that results has four parts: clean and re terminate the corroded connection, separate the hallway lights from the elevator, replace the emergency light batteries, and ask each owner who added cooling to supply nameplate data so the load can be reviewed. The board schedules the work across two budget cycles, with safety items first. Nothing in this plan is dramatic, but it removes the most likely causes of a future outage.

Residents also have a role. A resident who notices a warm outlet, a flicker that repeats, or a smell near the meter room should tell management the same day, with a note of the time and what was running. Management that logs these reports can spot patterns, such as complaints clustered on one riser, long before a failure. A one page timeline of repairs, with dates and photographs, is useful to the next board and to any buyer or insurer who asks. Keep copies where more than one board member can reach them, so the knowledge does not depend on a single person.

Blocks and landmarks this page covers

This page covers the buildings beside the Hollywood Beach Broadwalk, along State Road A1A, and toward the Intracoastal Waterway, including small apartment houses, older condominiums and mixed use buildings with shops at street level.

Nearby places and related reading

For the center of the city, see downtown Hollywood. For the broader view, see our Hollywood page. Related guides cover commercial electrical service and how king tides affect ground level electrical equipment.

Talk to us

Call to describe your building near the Broadwalk. A quote can start by phone, and shared systems need an on site visit.
Call (954) 378-8564
Call (954) 378-8564