Call (954) 378-8564
Home / Service Areas / Hollywood Hills

Electrician for Hollywood Hills Homes From the Mid Century Build Out

Many homes in Hollywood Hills were built in the decades after the war, when a house needed a fraction of the power a family uses today. This page is for long term owners near Sheridan Street and Pembroke Road who want to understand panels, circuits and updates in plain terms.
Illustrative photograph
Illustrative photograph

Understanding a house built for a different kind of household

When the first wave of block homes went up across this part of Broward County, the electrical plan was simple. A house typically had a handful of lighting circuits, a few outlets in each room, one or two circuits for the kitchen, and a modest service from the street. The family owned a refrigerator, a stove, a radio or early television and perhaps a window fan. Air conditioning, if it existed at all, was a single window unit. That modest picture explains a great deal about what an owner finds behind the walls today.

Since then, a typical household has added computers, chargers for every pocket, a microwave, a dishwasher, a washer and dryer, central air conditioning, and often a second television in nearly every room. Each device is reasonable by itself. Together they ask much more of a system that was drawn up when the list was short. The result is not necessarily danger, but it is often strain, and strain shows up as breakers that trip, outlets that run warm and lights that dim when a large appliance starts.

A concrete block house has its own character. The walls are solid, which is a virtue in a storm and a challenge for wiring. Cable in a block home often runs in the ceiling space and drops down through channels, or it is set into the block as it was built. Adding a new outlet in the middle of a block wall is a different job than adding one in a wood framed wall. Surface mounted conduit, careful cutting into the block, or running from the attic are all options, and an electrician chooses the least disruptive route for each case.

Owners who have lived in their homes for a long time often know its quirks better than anyone. They know which outlet works only when wiggled, which switch crackles, and which light has been on its own circuit forever. That personal knowledge is valuable on a visit. It points to the spots where an inspection should begin, and it helps separate normal behavior of an older house from signs that something has changed.

The goal for a home like this is not to rip everything out. Many mid century systems remain serviceable when they are kept dry, not overloaded, and brought up to date where it matters. The useful questions are which parts are doing fine, which parts are working beyond their design, and which upgrades give the most safety and comfort for the least disruption. The sections that follow take those questions in turn, starting with the panel that sits at the center of everything.

When the panel and service no longer match the way you live

The panel is where the story of a mid century house often becomes obvious. Older panels may be small, with only a few breaker spaces. Over the years owners ran out of room and added breakers where they could, sometimes squeezing two circuits onto a single position when the panel allowed it, and sometimes adding a second small panel to catch the overflow. Those fixes worked at the time, but they can leave a tangled arrangement that is hard to label and harder to troubleshoot.

Consider what a panel replacement looks like in practice. The electrician first confirms the size of the service coming from the utility and calculates the real electrical demand of the house. That calculation weighs the air conditioning, the kitchen, the water heater, the dryer and everything else that can run at once. If the existing service has headroom, a new panel of the same capacity may be enough, giving more breaker spaces and modern protection. If the demand is close to the limit, the service itself may need to grow, which involves coordination with the utility and the local permit office.

Warning signs that a panel deserves attention include breakers that feel loose or will not stay reset, scorch marks or discoloration around the box, a buzzing sound, and the smell of something hot near the panel. Any of these is reason to call promptly. Meanwhile, a panel that simply looks old is not automatically unsafe, but its age tells you the equipment inside may no longer be the type that is recommended today, and replacement parts may be difficult to find.

Here is a short list of questions to bring to a conversation about the panel:

  • How many circuits are in use, and how many open spaces remain?
  • Is the main breaker size appropriate for the demand of the house today?
  • Are there any double tapped breakers or signs of overheating?
  • Is the panel clearly labeled so that anyone in the family can find the right breaker?
  • Would adding a charger, a larger air conditioner or a pool in the next few years change the answer?

That last question is a practical one. A panel chosen for today's needs alone may be outgrown quickly. A panel chosen with sensible room to grow costs a little more at the start and saves a second disruption later. An electrician can help you weigh the options without pushing you toward anything you do not need.

Worked example: a retired couple near Sheridan Street decided to replace an aging air conditioner with a larger central system and add a washer and dryer in a converted carport corner. Their old panel was nearly full and the service was modest. After a load calculation, the plan called for a new panel with more spaces, a dedicated circuit for each new appliance, and a coordinated service change. Because the work needed a permit and an inspection, the project took a few steps, but afterward the house had a clean, labeled panel and room for the next change. Their experience is a reminder that the first conversation about one appliance often turns into a conversation about the whole system.

Circuits room by room: kitchens, baths, bedrooms and garages

Thinking room by room is often the clearest way to see what an older home needs. Each room has its own electrical habits, and each has changed since the house was built.

The kitchen is the busiest. Original kitchens might have had a couple of outlets and a single circuit. Today a kitchen runs a refrigerator, a microwave, a dishwasher, a disposal, small appliances on the counter and maybe an induction or electric range. Current practice calls for several separate circuits in a kitchen, with protection on the countertop outlets. If your kitchen still shares a circuit with the dining room, you may notice that the toaster and the coffee maker cannot run together without a trip. That is the circuit telling you it was never designed for this much.

Bathrooms come next. Moisture and electricity meet here, so outlets near sinks and tubs should have ground fault protection, and fans and lights should be rated for the conditions. Older bathrooms sometimes have a single outlet beside the mirror on the same circuit as the bedroom lights. A hair dryer on that circuit can cause a trip, and without protective devices the setup is less safe than it should be. Adding a dedicated, protected circuit is a straightforward improvement.

Bedrooms and living areas are where cords multiply. Fewer outlets than needed leads to power strips and extension cords, sometimes plugged into other strips. That daisy chain is a common cause of overheating, because the whole chain draws through a single plug in the wall. Adding outlets where they are needed is one of the simplest and most valuable updates in an older home. In block construction, the electrician may use surface raceways or channels that look neat and avoid cutting into masonry.

The garage or converted carport is the place where change is greatest. Many mid century homes have a garage that now serves as a laundry room, a workshop, a gym or an extra bedroom. These uses need proper circuits, adequate lighting and protected outlets. A converted space that relies on an extension cord from the next room is a risk waiting to happen. A planned set of circuits turns the space into something safe and useful.

Outside, patios, carports and yards often have lights and outlets added in stages. Rain, sun and sprinklers all test these. Weatherproof covers, proper fixtures and ground fault protection are the baseline. If you notice discolored covers, cracked housings or lights that fail after rain, they are due for replacement.

One more habit helps: walk through each room with a small outlet tester or simply by checking that each outlet holds a plug snugly and does not feel warm. Notes about which rooms feel underserved are worth sharing with the electrician. A room by room plan lets work be done in stages, which can fit a budget and spare you from living through one large project.

Grounding, protection devices and what modern standards add

Two quiet features separate older electrical systems from current ones: grounding and protective devices. Neither shows up in the daily experience of using a light switch, yet both matter greatly when something goes wrong.

Grounding provides a safe path for stray current to travel when a fault occurs, such as a hot wire touching the metal casing of an appliance. In a grounded system, that fault trips the breaker quickly. In an ungrounded system, the casing can stay energized until someone touches it. Many mid century homes have two slot outlets in some or all rooms, a visible sign that grounding may be absent in those circuits. Replacing a two slot outlet with a three slot outlet without addressing the missing ground is not a solution, because the third hole then connects to nothing.

There are legitimate ways to improve a situation like this. One is to run new wiring with a grounding conductor to the affected outlets. Another is to install ground fault protection on the circuit, which monitors for leaking current and shuts off power quickly. Which is right depends on how the house is wired, how accessible the wiring is and what you plan to plug in. Valuable electronics such as computers benefit from a true ground, so those locations are usually priorities.

Protective devices have evolved as well. Ground fault protection is now expected in kitchens, bathrooms, garages, outdoors and other damp areas. Arc fault protection is designed to detect the signature of a damaged or loose connection that could start a fire, and it is expected in many living areas of newer construction. Adding such protection to an older home is possible through special breakers in the panel or specialized outlets. A good conversation covers which circuits benefit most, which devices are appropriate for your panel, and how to test them.

Surge protection is another modern layer. Homes near the coast see thunderstorms often, and sensitive electronics suffer from voltage spikes. A protective device at the panel handles the largest surges, while plug in protectors cover individual devices. The two work together, and neither is a substitute for the other.

Smoke and carbon monoxide alarms complete the picture. Alarms that are interconnected, so that one sounding triggers all, give earlier warning in a house with several bedrooms. Older houses may have a single alarm in a hallway that has long since passed its useful life. Replacing alarms on a schedule, and testing them monthly, is simple and valuable.

None of this means an older home is unsafe to live in. It means the home was built to the standards of its day, and there are sensible ways to bring the most important protections forward. The best approach is to prioritize: address any visible hazards first, then add protection where the risk is highest, and fold other updates into projects you were planning anyway.

Staying in the house you know and updating it in stages

Many owners in Hollywood Hills plan to stay in their homes for a long time. That changes the way to think about electrical work. Instead of fixing only what is broken, a long term owner can plan a sequence of updates that spreads cost and disruption over time and ends with a system that suits the way they live.

A sensible sequence usually begins with safety. If there are signs of overheating, damaged wiring, missing covers or an overloaded panel, those come first. Next come the changes that improve daily life: more outlets in the rooms that need them, better lighting, a dedicated circuit for a heavy appliance. After that comes the planning of future needs, such as a place for a car charger, a standby generator connection or rooftop solar. Putting the infrastructure in place early, even if the equipment comes later, avoids repeating work.

Aging in place deserves a mention. Good lighting reduces falls, switches at the right height and location make rooms easier to use, and outlets within comfortable reach help people who do not want to bend. Night lights on hallways, motion activated fixtures and clear, labeled panels all contribute to comfort and safety. These are small projects with real benefit, and they fit well into a long term plan.

Resale is a different but related consideration. Even if you do not plan to sell soon, a clean and well documented electrical system helps the day it happens. Buyers and their inspectors look at the panel, the grounding, the outlets and the age of equipment. A house with an updated panel and a record of permitted work moves through that process with fewer surprises. Keeping receipts and photos of completed work is a habit worth forming.

Energy use is another reason to update. Older lighting can be replaced with efficient fixtures, reducing heat and cost. Ceiling fans with proper support and wiring help move air and soften the load on air conditioning. Thermostat wiring, if you are adding a smart model, sometimes requires a common wire that older systems lack, which is a small job for an electrician but a surprise for a do it yourself project.

It is wise to ask for work to be explained in stages. A good electrician describes what each step accomplishes and which steps can wait. You can choose the pace. Some owners prefer to do everything at once, while others prefer smaller steps over several seasons. Both are reasonable, as long as safety items are not postponed.

Finally, keep an eye on seasonal habits. Before the hottest months, a quick check of the air conditioning circuit, the outdoor disconnect and the condenser wiring helps avoid a failure in the middle of a heat wave. Before storm season, a look at surge protection and a plan for outages helps you feel ready. Small, regular attention keeps a mid century house running comfortably for years.

How a project on a block home is staged from first call to finish

Knowing the shape of a project makes it feel less daunting. Here is how electrical work in a mid century block home usually unfolds.

It begins with a phone call. You describe what you want done or what problem you are seeing, along with the age and construction of the house. For simple tasks, a quote may be possible after that conversation. For anything that touches the panel, requires new circuits through block walls or involves the service, an on site visit is needed. The electrician has to see the house to give an honest answer, because masonry, attic access and the state of existing wiring all change the work.

At the visit, the electrician looks at the panel, traces key circuits and asks about your plans. They check how accessible the attic is, whether there is room to route cable, and where finishes can be protected. They may point out issues you did not ask about, and a good one explains which are urgent and which can wait. You leave with a clear idea of the scope and a written estimate that describes the work.

Permits come next for work that requires them. A panel change, a service upgrade or a new circuit for certain equipment typically needs a permit and an inspection. The city permit office is the authority on what applies, and your electrician handles the process. Inspections protect you, because a second set of trained eyes confirms the work meets the code.

On the day of work, expect power to be off for part of it, especially for a panel replacement. Plan to protect food in the refrigerator, charge devices ahead of time and keep pets in a safe room. Floors and furniture near work areas should be covered. In block homes, cutting into walls produces dust, so it helps to clear the area and seal doorways. A tidy work site is part of a respectful job.

When the work is done, there is testing. Each new circuit is checked, protective devices are tested, and the panel is labeled. The inspector visits to confirm, and then you receive the finished system. Ask for a walkthrough, and ask where the main shutoff is, how to reset breakers and how to test protective outlets.

Afterward, living with the changes is simple. Keep the updated panel directory handy, test ground fault devices monthly, and let the electrician know if anything seems off in the weeks following. Most issues, if they appear, show up early.

If you own a home in Hollywood Hills and have wondered what your wiring can handle, call and describe it. A conversation about what you have and what you want is the best starting point, and it will tell you whether a quick fix, a staged plan or a full update fits your home.

Settings in Hollywood Hills this page speaks to

Hollywood Hills is a residential part of Hollywood with streets of established single family homes, many from the mid century build out. These situations come up often.

  • Block homes near Sheridan Street and Pembroke Road where the panel and service were sized for a smaller household.
  • Houses with two slot outlets or limited outlets per room, where cords and power strips have multiplied.
  • Converted garages and carports that now serve as laundry rooms, offices or extra bedrooms.
  • Long term owners who want a staged plan for panels, circuits and safety devices instead of one big project.
  • Homes preparing for a new central air conditioner, a charger or solar, where the panel needs room to grow.

If your home is different, describe it by phone and the visit can be shaped to fit.

Nearby places with related pages

Neighbors may also want to read the pages for Hallandale Beach and Hollywood Lakes, which describe different housing. Our guide on storm damage electrical repair covers what to do after weather events, and the guide on electrical steps before you evacuate helps with planning ahead.

Talk to us

Call to talk through your Hollywood Hills home. A quote can begin by phone, and larger work gets an on site visit first.
Call (954) 378-8564
Call (954) 378-8564