Call (954) 378-8564
Home / Service Areas / Sheridan Street Corridor

Homes and Shops Around Sheridan Street Between Dania Beach and Hollywood

Sheridan Street links Dania Beach and Hollywood and carries a mix of homes, shops, offices and light industrial buildings. This page speaks to owners along that stretch, from Federal Highway to Interstate 95 and beyond.
Illustrative photograph
Illustrative photograph

A road that belongs to two cities at once

Sheridan Street is the kind of road that stitches communities together. It runs east and west across the line between Dania Beach and Hollywood, crossing Federal Highway and passing under or beside Interstate 95 on its way inland. Along it, the character shifts block by block: residential streets with older houses and newer townhomes, strips with small shops and services, medical and professional offices, and buildings that house light industrial or trade uses.

For electrical work, that blend means no single description fits. An owner on one block may have a modest block house from the middle of the last century. An owner a few blocks over may have a newer townhome with a compact panel and a tight garage. A business owner nearby may run a small workshop that uses three phase equipment. The common thread is that all of them live with the same climate, the same utility and the same regulations, and all of them feel the effects of a busy road.

The road also affects how work is done. Parking can be limited, driveways narrow, and access to buildings constrained by traffic and neighbors. A job that needs a truck close to the building or a lift for work on a mast may need planning. Utility work, such as disconnecting a service, can be scheduled in ways that consider traffic and nearby customers.

Because Sheridan Street touches two cities, owners sometimes wonder which city's building department applies. The answer depends on which side of the boundary the property sits, and the address or the county records will say. Permit and inspection procedures can differ slightly, so a good electrician checks first. Never assume the rules are the same just because the road is the same.

This page is a general guide for owners along the corridor. It does not describe any specific property, and it is not a replacement for an inspection. A quote can begin with a phone conversation in which you describe the building and the problem. For anything involving the panel, the service, hidden wiring or a business's continuity, an on site visit is the right start. In the sections below we walk through the themes that arise most often.

Homes on and near the street: older panels and newer needs

The homes within a few blocks of Sheridan Street span a wide range of ages. Many are one story block houses with stucco exteriors, built when a family's electrical needs were smaller. Some have been updated with new kitchens, impact windows, new roofs and added rooms. Others are largely original. The wiring in each tells a story.

Older homes frequently have panels that are nearing the limit of their capacity. A panel that had open spaces decades ago is often full today, with tandem breakers or added sub panels squeezed in. Tandem breakers, which place two circuits in one slot, are allowed only in panels designed for them, and using them where they are not rated is a hazard. If you notice breakers crowded together, or a panel with labels like extra or new on a hand written strip, it is worth a look.

Another feature is the mix of conductors. Some older houses contain cloth insulated wire, which becomes brittle. Others have aluminum branch circuit wire from a certain era, which requires special connections. Many have a blend of the original wiring and later additions, sometimes joined with improper splices in the attic or inside a wall. An electrician looking at a house will check the condition and type of wiring where it can be seen and tested, and will talk through what is a concern and what is acceptable.

Common upgrades for homes in this area include:

  • Replacing an outdated panel with a modern one with room for growth.
  • Adding ground fault protection in kitchens, baths, garages and outdoors.
  • Adding arc fault protection where required for renovated rooms.
  • Installing a surge protective device to guard against storm and grid surges.
  • Adding circuits for air conditioning, a charger, a pool or a workshop.
  • Replacing worn outlets and switches that feel loose or have scorch marks.
  • Upgrading smoke and carbon monoxide alarms.

Homes close to the interstate and busy roads may notice more dust and soot on exterior fixtures and equipment, which can hold moisture and speed corrosion. Cleaning exterior covers and checking seals helps. Windows and doors facing the road may hold security systems and cameras that need power. Keep those on proper circuits, not on a single overloaded outlet.

Finally, townhomes in the area often share walls and sometimes share service equipment. If a problem seems to affect more than one unit, talk with your association or neighbors. A single failing connection in a shared meter bank can produce symptoms in several homes at once.

Shops, offices and light industrial buildings

West of Federal Highway, and toward the interstate, Sheridan Street has a different feel. Here there are office suites, medical practices, repair shops, distribution spaces, contractors' yards and similar businesses. Each has its own electrical story.

Offices and medical practices depend on clean, steady power. Computers, networks, phones, imaging equipment and lab devices are sensitive to voltage disturbances. A surge protective device at the panel, with point of use protection and uninterruptible power supplies for critical equipment, helps. Dedicated circuits for equipment that needs them reduce interference. Good grounding is essential, because poor grounds cause odd faults and noise. In a medical office, there are additional rules for patient care areas, which a qualified professional should handle.

Light industrial users bring heavier loads. Compressors, machining tools, kilns, ovens, welders and conveyors need circuits sized to their nameplates, proper disconnects and protection. Three phase service may be present, and it is a special case that deserves a careful on site look, because balanced loads, phase rotation and the right protective devices matter. A motor that runs backward or a phase that is lost can damage equipment. Any change to three phase systems should be done by experienced professionals.

Warehouses and storage spaces often have high ceilings, large lighting loads and forklifts that charge in a corner. Lighting is an area where upgrades pay off. LED high bay fixtures use less power and last longer than older types. Battery charging stations for forklifts or carts need appropriate ventilation and circuits. Dock doors, roll ups and controls need power and often low voltage control wiring.

Contractors' yards have their own concerns. Temporary power, trailers, outdoor outlets and tools used in the open all need ground fault protection and weather rated equipment. Cords should be heavy duty and in good condition, kept off the ground where possible and out of puddles.

For all these spaces, labeling and documentation matter. A one line diagram, even a simple hand drawn one, helps future electricians understand the system. Keeping it updated as changes are made prevents confusion and cuts the cost of future work. Include notes on voltages, phases, breaker sizes and the loads they serve.

Finally, remember that tenants in multi tenant buildings may share risk. A problem in one unit can affect others, and a fire in one can damage all. Good maintenance and clear communication are in everyone's interest.

Highway noise, vibration and power quality

Living and working beside a major interstate has environmental effects. Noise, dust and vibration are the obvious ones. Electrical effects are subtler but real, and they influence how a property should be wired and maintained.

Vibration is the most direct. Heavy trucks produce low frequency vibration that travels through the ground and into buildings. Over years, it can loosen screws and connections. A loose connection is a high resistance connection, and high resistance creates heat. Panels, receptacles, switches and light fixtures in buildings near the highway benefit from an occasional check for tightness. If you hear buzzing, smell hot plastic, or see a flickering light that responds to traffic, mention it.

Dust and soot from vehicles settle on outdoor fixtures, meters and equipment and can hold moisture. That makes them corrode faster. Cleaning with a damp cloth when the power is off, and inspecting seals and gaskets, helps. Replace covers that are damaged. If a fixture has become brittle in the sun, replace it before it fails.

Power quality is another theme. Large industrial users, heavy equipment and the grid itself can cause momentary dips and spikes. A refrigerator or air conditioner that clicks off and back on, a clock that resets, a computer that reboots, may all be responding to a power event. A surge protective device at the panel defends the whole house or building. Point of use devices defend sensitive equipment. A battery backup protects a computer or a register from short interruptions.

Lightning is a concern across Florida, and tall structures and open lots near the interstate may be exposed. Proper grounding and bonding give lightning and fault current a safe path. Grounding electrodes, clamps and connections should be inspected from time to time, because corrosion and damage can break the path without any visible sign. Our page on grounding and bonding is a good companion read.

Finally, think about noise inside buildings. Humming transformers, buzzing dimmers, noisy ballasts and rattling fixtures can be sources of annoyance. Replacing them with quieter equipment improves comfort. Choose dimmers that match the lamp type and electronic equipment that is quiet in operation. Sometimes a hum indicates a loose connection or an overloaded circuit, so do not simply tolerate it. Have it checked.

These topics may sound technical, but in practice they come down to a few habits: check, tighten, clean, protect and ask when something seems off.

Mixed use buildings and the apartment over the shop

Along streets like this, it is common to find buildings that mix uses: a shop below and an apartment above, an office in front of a home, a house converted to a small business, or a duplex with one half rented to a trade. These buildings pose special electrical questions.

The first is separation of services. Ideally, each use has its own meter and panel, so that bills, responsibilities and shutoffs are clear. In many older mixed buildings, one meter feeds everything, and the owner divides costs informally. That can lead to confusion and disputes. If the building is being renovated or the tenant mix changes, consider whether separate services make sense. Doing so involves the utility, a permit and equipment changes, and it should be planned carefully.

The second is safety. A fire or electrical fault in the commercial space can threaten people living above. Smoke alarms and carbon monoxide alarms should be present and interconnected where required. Fire separation between spaces should be preserved when wiring is run. Penetrations through fire rated walls and floors must be sealed. Emergency lighting and exit signs may be required in the commercial portion.

The third is load. A restaurant, salon or workshop below an apartment may have heavy equipment that affects the building's service. Cooking equipment, hair dryers, heaters, compressors and display refrigeration add up. The residential part of the building will have its own loads: air conditioning, an oven, a dryer and lights. A load calculation for the entire building tells you whether the service is adequate. If it is not, an upgrade should be planned before adding new equipment.

The fourth is clarity of responsibility. If the owner lives upstairs and rents the downstairs, or the reverse, who pays for electrical repairs? Who has access to the panel? Who calls the electrician? Put it in writing. If the building has multiple tenants, ensure that the panel for each unit is accessible to that unit's occupants but protected from tampering.

Finally, accessory structures such as rear sheds, garages and storage rooms are often added over time. They are fed from the main building through underground or overhead cable that may be undersized or poorly protected. A review of the feeder, the disconnect and the sub panel can reveal hidden risks. An electrician will check conductor size, protection and grounding, and recommend corrections. Add ground fault protection where moisture is present.

Treat every mixed building as a puzzle, solved one piece at a time with a plan.

One last practical idea for owners along a long road like this is to compare notes with neighbors. Owners on the same block often share the same utility feeder, the same pole and the same trouble with storms or surges. If three buildings lose power at the same moment, the problem is probably outside your walls, and the utility is the right call. If only yours does, the cause is on your side. Keeping a simple log of outages, with the date, time and what you noticed, helps sort the two apart and helps an electrician narrow the search.

Planning, permits and scheduling around a busy road

Good electrical projects begin with good planning. On a busy street, a bit of foresight makes the difference between a smooth job and a frustrating one.

Begin by describing the problem or goal clearly. Take photographs of the panel, the equipment and the symptoms. Note when the problem occurs and what is running. If you are planning an addition or a new piece of equipment, gather its nameplate information or specification sheet. Share the information when you call. A quote can be discussed by phone for simple work, and anything complicated needs an on site visit.

Understand which jurisdiction applies. Because Sheridan Street straddles two cities, the property's address determines the building department and the rules. The county may also play a role. A reputable electrician will know the process and handle the permit. As the owner, you should expect to receive a copy of the permit and the final inspection approval.

Think about access and parking. If a truck or lift needs to reach the building, tell the electrician. Check whether on street parking is restricted. If the work requires traffic control or closing a driveway, plan with neighbors. For businesses, schedule work outside peak hours if possible, and decide in advance which areas must stay powered.

Plan for shutdowns. Some jobs require turning off power to the building or to a section. Ask how long, and prepare. Protect computers and refrigeration. Tell staff and tenants. For residential jobs, think about pets, medical equipment and food storage. Charge devices ahead of time.

Consider timing relative to storm season. Major upgrades are easiest to schedule outside the busiest weeks of hurricane season, when demand for electricians surges. If you plan a generator inlet or a panel upgrade, do it before the season, not during a watch.

Budgeting is part of planning. Ask for a written scope that lists what is included. Ask whether permit fees, inspection scheduling and cleanup are part of the proposal. Ask what happens if hidden problems are found. Honest contractors explain these things up front. Be cautious of any quote given sight unseen for work that involves a panel, service or hidden wiring.

When the work is done, walk through it with the electrician. Test the new circuits, review the panel directory and keep the paperwork. Add the project to your property records. A well documented property is easier to maintain, insure and sell.

Two worked examples show how this plays out. In the first, the owner of a small block house a few streets off the road wants to add a central air conditioner to replace window units. The electrician looks at the panel, finds a hundred amp rating with no spare spaces, and calculates the load with the new system included. The plan has three steps: replace the panel with one that has room, add the dedicated circuit for the condenser sized to its nameplate, and schedule the work in the cooler part of the year so the household is not without cooling for long. The permit is pulled, the inspector looks at the work, and the family keeps a folder with the paperwork.

In the second, a tenant who runs a small cabinet shop in a light industrial unit wants to add a dust collector and a larger table saw. Before buying, the tenant calls and describes the machines. The electrician asks for the nameplate data, learns that the saw needs a motor circuit, and explains that the dust collector must not share a circuit with the lights. A short visit confirms that the unit has single phase service with limited capacity, so the tenant chooses machines that suit it, and the landlord approves a sub panel. Asking before buying avoided a costly return and a month of tripped breakers.

Both stories have the same lesson. Describe the goal, share the numbers, and ask what the building can carry before committing money to equipment. The few minutes it takes to do that on a phone call can save weeks of frustration.

Stretches and crossings this page covers

This page covers the length of Sheridan Street between its meeting with Federal Highway and its passage near Interstate 95, including homes on adjoining streets and the shops, offices and light industrial buildings that line the road.

Nearby places and related reading

To the south, see our Hollywood page. To the east, see Federal Highway in Dania Beach. Related guides cover dock and boat lift power and what to expect when power returns after a storm.

Talk to us

Call to describe your property near Sheridan Street. A quote can start by phone, and larger jobs need an on site visit.
Call (954) 378-8564
Call (954) 378-8564