
Following the path of power from the street to the main breaker
It helps to picture the route electricity takes to reach your home. Power travels along lines on poles or underground cables in the street, reaches a transformer that steps it down to household voltage, and then passes along a service drop or a buried service lateral to your property. At the house, the service conductors connect to a weatherhead or an underground entrance, run through a mast or conduit, and arrive at the meter base mounted on an exterior wall. The meter sits in that base and measures use. From the meter base, conductors continue to the main disconnect, which may be a breaker at the panel inside or a separate unit outside, and then to the branch breakers that feed the rooms.
The important idea is that there are two zones. The first zone runs from the utility to the main disconnect. In that zone, nothing in your house can switch the power off, because you are upstream of your own main breaker. The second zone runs beyond the main disconnect, where your breakers do control the power. Storm surge, which is a rise in sea level driven ashore by a storm, can affect both zones, but the first zone is more dangerous because it can stay energized while submerged.
Dania Beach sits near the coast, and parts of the city are low. The Dania Cut-Off Canal and the Intracoastal Waterway can rise in a major storm and push water into streets and yards. Homes with meters mounted low on exterior walls, or with underground service entrances, are more exposed than homes with elevated equipment. Exactly which streets and addresses are affected varies by storm, and local emergency management maps give guidance about flood zones. Your own property's risk is best understood by checking those maps and by asking the local building department about requirements for equipment height.
This page is general education about how the equipment works and how water affects it. It does not predict flooding at any address and it does not replace instructions from the electric utility or emergency officials. When water reaches electrical equipment, the safe response is to stay away and call the people trained to deal with it.
With the path in mind, you can see why a flooded meter is more than a nuisance. It sits at the junction of the utility's equipment and yours, and it is the place where the question of who is responsible for what can matter a great deal after a storm.
Who owns what: the utility, the owner and the line between
Confusion about ownership slows down repairs after storms, so it is worth understanding the usual division. Practices vary, so confirm the details with the electric utility, but a general picture holds in many places.
The utility generally owns the lines and equipment up to a connection point, along with the meter itself. The customer generally owns the equipment from that point onward, which typically includes the mast or conduit that carries the service conductors down to the meter, the meter base, the conductors beyond the meter, the main disconnect, the panel and the wiring in the house. In an overhead service, the point where the utility's drop wires attach to your service conductors, at the weatherhead, is a common dividing line. In an underground service, the dividing line may be at the property line, at a pad mounted transformer, or at the meter base, depending on the arrangement.
Here is why that matters after a storm:
- The mast and meter base are usually the owner's responsibility. If a tree pulls the mast over, or water ruins the base, repairs fall to the owner and an electrician.
- The meter belongs to the utility. Only the utility removes or reinstalls it.
- The service drop belongs to the utility. If it is down, the utility handles it.
- Coordination is required. An electrician repairing a mast or base needs the utility to disconnect power before work and reconnect after.
- Inspection is usually required. The building department may need to approve the work before the utility reconnects.
This is why a storm can leave a home waiting for days even after the neighborhood has power. If the mast is bent or the meter base is damaged, the utility cannot safely reconnect until the owner's side is repaired and inspected. Residents often misunderstand this and feel the utility is slow, when the delay is waiting on an electrician and an inspector.
It also explains why you should never touch the meter or the service wires, even if the house is dark. The line side of the meter can be energized at all times. Cutting or moving service wires can kill. Only qualified utility crews and licensed electricians working in coordination with them should handle that equipment.
If you are unsure which pieces are yours, ask the utility before a storm, not after. A short call to the customer service line or a look at the utility's website can clarify what they consider the point of connection for your home. Writing that down and adding it to your storm folder helps.
What rising water actually does to the equipment
Surge arrives as a rise, often fast, of dirty, salty, debris filled water. Its effects on service equipment are specific.
The meter base is a metal enclosure with openings where the conductors enter and leave. It is designed to resist rain, not submersion. Once water rises above the lowest opening, it enters. Inside are the meter jaws and bus bars that carry the full current of the home. Water bridging live parts can create short circuits and arcing. Salt water speeds corrosion on the jaws and terminals, and silt settles inside. Even after the water drops, the corrosion continues, and connections can overheat later.
Conduits and masts can hold water. A conduit that runs underground to the base can fill with water that reaches the panel. Conductors inside may be damaged by salt, since the insulation can be compromised at splices and terminations.
The main disconnect and panel, if low, face the problems discussed in the guide about flooded outlets and panels. Outdoor disconnects, subpanels and pool equipment also sit in exposed spots.
Wind often arrives with surge and affects the overhead portion. A mast is a lever. Wind on the service drop and on tree branches that fall on it can bend or tear the mast and the weatherhead and pull the base away from the wall. A cracked or loosened base lets water in, and exposed conductors are a hazard.
Debris carried by moving water strikes equipment. A floating object can break conduit, tear a meter base or knock down a pedestal. Underground service pedestals and pad mounted equipment on the street side can be submerged or undermined.
Signs after a storm that the service equipment has been affected include:
- A water line or mud on the meter base or wall.
- A meter that is tilted, cracked, missing or has moisture inside its glass.
- A mast that is leaning, bent or pulled from the wall.
- A weatherhead that is cracked or hanging, or wires pulled tight or hanging low.
- Rust, green or white crust, or a burnt smell at the base.
- Sparking or buzzing at the meter, which means stay away and call at once.
None of these should be inspected up close. Look from a distance, take photographs, and call. If there is sparking, smoke or fire, treat it as an emergency and call emergency services and the utility.
Height, placement and planning for low ground
You cannot stop a surge, but you can influence where your equipment sits and how it is built. Planning decisions made during a renovation or a repair can reduce the risk of the next flood.
The central idea is elevation. Equipment mounted higher on a wall has a better chance of staying dry than equipment near the ground. Building rules for areas with flood risk often include requirements about how high electrical equipment must be placed relative to a reference flood elevation. These rules are set by building codes and flood programs, and they change over time. The city building department can tell you what applies to your property, particularly if you are doing a substantial repair or renovation after damage. Do not guess. Ask them, and ask a licensed electrician to explain what the requirements mean for your service.
Common choices that homeowners and professionals discuss include:
- Raising the meter base and main disconnect. Moving them higher on the wall or onto a platform or support above expected water. This involves the utility and a permit.
- Relocating the panel. A panel on an upper floor or an elevated platform is safer in flood prone areas than one in a ground level garage.
- Strengthening the mast. A properly braced mast resists wind better. The type of mast and its attachment are regulated.
- Sealing conduits. Sealing entries and using appropriate fittings reduces water entering buried and wall conduits.
- Choosing corrosion resistant materials. Equipment rated for outdoor and corrosive exposure lasts longer in coastal air.
- Adding surge protection. A protective device at the service entrance helps with electrical surges, though it does nothing for water.
It is worth separating two kinds of surge. Storm surge is the rise of water. Electrical surge is a spike in voltage. They share a name, and both can arrive in a storm, but they call for different protections. Elevation and sealing address water. Surge protective devices address voltage spikes.
Planning also includes thinking about the neighbor's equipment, the street and the utility. A pedestal or transformer near your home may be the utility's responsibility, and its condition affects your restoration. You cannot change it, but you can report damage.
Documentation helps. Photograph your meter base, mast and panel in good condition. Record the heights of equipment above ground. If you later file an insurance claim, these records show the pre storm condition.
Finally, ask an electrician about your service size and condition. A service entrance that is old, corroded or undersized is more vulnerable to storm damage. A professional can advise whether replacing parts of it makes sense when you do other work.
After the water recedes: look, document, wait
When the water goes down, the urge to get things back to normal is strong. For service equipment, the safest approach is patience and documentation.
Do not approach the meter or service equipment if there is any chance it is wet or damaged. Stay out of standing water. If the base appears damaged or was submerged, assume it is unsafe. Call the utility to report the situation and ask about disconnection. Utilities commonly require that flooded service equipment be inspected and often replaced before reconnection. If you are told to wait, wait.
Photograph everything from a safe distance: the water line, the meter and base, the mast, the weatherhead, the panel and anything that looks damaged. Note times and dates. This documentation supports insurance claims and helps professionals plan.
Arrange for a licensed electrician to evaluate the service. They will confirm that power is off, inspect the equipment, and test conductors and connections. They may recommend replacement of the meter base, the mast, the service conductors, the main disconnect and the panel, depending on the damage. They will explain what permits and inspections are needed, and how to coordinate with the utility.
A few details may surprise people:
- Even if the meter base looks intact, salt water inside can compromise it.
- Conductors inside a conduit that filled with water may need replacement.
- A panel that was dry may still need checking if the water reached the service above it.
- The utility may remove the meter and hold it until the owner's side has passed inspection.
- Temporary power arrangements can sometimes be made for repairs, subject to rules and inspections.
Cleanup requires care too. Do not hose down electrical equipment. Do not scrape corrosion from live parts. Do not apply chemicals or sprays. Leave cleaning to the professionals who will determine what can be reused.
If you have a generator, keep using it only with safe connections. Do not connect it to the house wiring through an outlet or with an improvised cord. A damaged service means that backfeeding could endanger line workers and people in your home. A guide on this site covers generator safety in detail.
Expect delays. After a major storm, electricians and inspectors are busy, parts can be scarce, and the utility has many reconnections. Patience is hard, but rushed work on service equipment is a safety risk. Keep in contact, keep records, and follow up politely.
Rebuilding smarter and getting reconnected
When the repair work begins, there is a chance to make the service more resilient. Even a modest step, such as raising or sealing equipment, can help in the next storm. Whether and how to do it depends on the property, the rules and the budget, and it is worth discussing before work starts instead of after.
A conversation by phone is the first step. Describe what you saw: how high the water reached, which equipment was wet, what the utility has done, and what you have documented. A quote follows that conversation. Because service equipment work involves coordination with the utility, permits, inspections and often decisions about relocating or upgrading, an on site visit is needed before anyone can outline a plan. Nobody can responsibly quote a firm figure for a flooded service without seeing it.
When an electrician visits, these are good questions to ask:
- Which parts of the service need replacement, and why?
- Do flood zone rules affect the height or location of the new equipment?
- Who arranges the permit and the inspection?
- How will the utility be coordinated for disconnection and reconnection?
- Can the mast, base and main be placed higher or protected better?
- Is the service size adequate for the home, including future loads?
Plan the order of the work. Typically, the utility disconnects, the electrician repairs or replaces service equipment, the inspector approves, and the utility reconnects. Interior repairs and drying may happen at the same time. Rewiring and replacement of damaged devices are completed and tested before the circuits are reenergized.
Once power is restored, make a point of checking the system again over the following days. Look at the meter and base for moisture, listen for buzzing, and watch for flickering lights or breakers that trip. Report anything unusual.
Think about the long term as well. Annual checks of the mast, base, weatherhead and panel keep small problems from becoming storm failures. Trim trees near the service with the utility's guidance, since they handle limbs near their lines. Keep drainage around the equipment clear, and maintain seals and covers.
Storm surge is a reminder that electrical systems share the home with the landscape and the sea. A low lying house can do only so much, but good placement, sound materials, honest maintenance and careful repair after damage go a long way. If you take away one idea from this page, let it be this: the meter at your house is the doorway for all your electricity, and when water reaches it, the right response is to step back, document, and let qualified people handle the doorway before anyone opens it.
A worked example makes the sequence clear. Imagine a canal side house where surge pushes water a few feet up the exterior wall. The meter base is mounted at chest height, so it stays dry, but the underground conduit that feeds the garage subpanel fills with salt water. The family sees the lights come back on in the street and assumes they can simply restore power. Instead, they call the utility, who confirm the meter is intact and that the dropped line is fine. An electrician checks the garage subpanel and finds water and salt in the lower breakers and in the buried conduit. The subpanel is replaced, the conduit is flushed and new conductors are pulled, the work is inspected, and power to the garage is restored days later. The main house had power earlier because its own panel sat higher. The lesson is that surge does not damage everything equally. Height, routing and material decide which parts survive.
Condominiums and small commercial buildings along the Federal Highway corridor and near the waterways face a version of the same story with larger equipment. Service rooms on ground floors, electric rooms below grade and rooftop equipment all have different exposure. Building managers should know where the main service enters, where transformers and switchgear sit, and what the plan is if the ground floor floods. Residents should ask their association about it before the season, since the answer affects how long everyone might wait for power after a major event.
It is also worth knowing how temporary arrangements work. After a storm, some homes receive a temporary service pole or a temporary meter arrangement so repairs can proceed, and these are subject to their own inspection and removal rules. They are not a way around the permanent repair. If someone offers to reconnect your service informally, skip the shortcut. An unapproved connection can leave you without insurance coverage for a later fire, and it endangers the people who work on the lines. The slower, inspected route is the one that protects you.